Search
IUPUI School of Engineering and Technology

IUPUI School of Engineering and Technology

Hamid Dalir

  • Associate Professor of Mechanical Engineering
  • Associate Professor of Motorsports Engineering
Hamid Dalir

317-278-4430
ET 201F
hdalir@iupui.edu
Professional Website

Education

  • Tokyo Institute of Technology, Mechanical Engineering, Ph.D., 09/2009
  • Sharif University of Technology, Mechanical Engineering, M.S., 11/2005
  • Ferdowsi University of Mashhad, Mechanical Engineering, B.S., 07/2003

Professional Experience

  • Associate Professor, Department of Mechanical and Aerospace Engineering, Syracuse University., 9/2015 - 9/2017
  • Airframe Structures Engineer, Bombardier Aerospace., 9/2011 - 8/2015
  • Postdoctoral Research Associate, Polytechnique Montreal., 9/2009 - 8/2011

Selected Publications

  • F. Michaud, H. Dalir and S. Joncas, “Structural design and optimization of an aircraft morphing wing: composite skin”, Journal of Aircraft, accepted, doi: 10.2514/1.C034340, (2017), 17 pages., 9/2017
  • X. Cao, H. Tian and H. Dalir, “Development of a new finite element simulation strategy for prediction of thermal and resin shrinkage deformations of composite parts during cure”, American Society for Composites 31 Technical Conference and ASTM Committee D30 Meeting (2016), Williamsburg, Virginia, USA., 11/2016
  • H. Dalir, “Damage tolerance coupon sizing of composite stiffened panels under impact”, IEEE International Conference on Mechanical and Aerospace Engineering (2016), pp. 68-72., 7/2016
  • H. Dalir, R. D. Farahani, L. Hernandez, C. Aldebert, M. Lévesque and D. Therriault, “Three-dimensional dielectrophoretic microparticle separator fabricated by ultraviolet-assisted direct-write assembly”, Journal of Nanoscience and Nanotechnology 16 (2016), pp. 765-771., 2/2016
  • R. D. Farahani, M. Pahlavanpour, H. Dalir, B. Aissa, M. A. E. Khakani, M. Lévesque, and D. Therriault, “Flow-induced orientation of functionalized single-walled carbon nanotubes embedded in epoxy using three-dimensional microfluidic networks”, Materials and Design 41 (2012), pp. 214-225., 8/2012
  • R. D. Farahani, H. Dalir, V.L. Borgne, L. A. Gautier, M. A. E. Khakani, M. Lévesque, and D. Therriault, “Reinforcing epoxy nanocomposites with functionalized carbon nanotubes via biotin-streptavidin interactions”, Composites Science and Technology 72 (2012), pp. 1387-1395., 8/2012
  • H. Dalir, R. D. Farahani, V. Nhim, B. Samson, M. Lévesque and D. Therriault, “Preparation of highly exfoliated polyester-clay nanocomposites: process-property correlations”, Langmuir 28 (2012), pp. 791-803., 8/2012
  • R. D. Farahani, H. Dalir, V.L. Borgne, L. A. Gautier, M. A. E. Khakani, M. Lévesque, and D. Therriault, “Direct-write fabrication of freestanding nanocomposite strain sensors”, Nanotechnology 23 (2012), pp. 1-9., 8/2011
  • H. Dalir, R. D. Farahani, V. Nhim, B. Samson, M. Lévesque and D. Therriault, “Microstructural and Mechanical Properties of Polyester/Nanoclay Nanocomposites: Microstructure-Mixing Strategy Correlation”, Material Research Society 1312 (2011), ii02-05 (9 pages)., 8/2011
  • R. D. Farahani, H. Dalir, Brahim Aissa, My Ali El Khakani, Martin Lévesque and Daniel Therriault, “Micro-infiltration of three-dimensional porous networks with carbon nanotube-based nanocomposite for material design”, Composites Part A 42 (2011), pp. 1910-1919., 8/2011
  • H. Dalir, T. Nisisako, Y. Yanagida, and T. Hatsuzawa, “DNA force-extension curve under uniaxial stretching”, Molecular Simulation 36 (2009), pp. 221-228., 8/2009
  • H. Dalir, Y. Yanagida, and T. Hatsuzawa, “Probing DNA mechanical characteristic by dielectrophoresis”, Sensors and Actuators B 136 (2009), pp. 472-478., 8/2009
  • H. Dalir, Y. Yanagida, and T. Hatsuzawa, “Multipolar electrical forces for microscale particle manipulation”, Journal of Computational and Theoretical Nanoscience 6 (2009), pp. 505-513., 8/2009
  • H. Dalir, S. Shayan Amin, and A. Farshidianfar, “Effects of Small length scale on vibrations of an embedded double-walled carbon nanotube”, Mechanics of Composite Materials 45 (2010), pp. 557-566., 8/2009

Awards, Honors, and Certifications

  • SyracuseCoE Faculty Fellow 2015-2017, Syracuse, New York, USA., 8/2017
  • Technical Advisor and Session Chair, American Society for Composites 31 Technical Conference and ASTM Committee D30 Meeting, Williamsburg, Virginia, USA., 11/2016
  • IEEE Best Paper Award, IEEE International Conference on Mechanical and Aerospace Engineering 2016, London, UK., 7/2016
  • Technical and Organising Committee, IEEE International Conference on Mechanical and Aerospace Engineering 2016, London, UK., 7/2016
  • Outstanding Faculty Award 2016, College of Engineering and Computer Science, Syracuse University., 5/2016
  • Gold Prize, NAMIS International School 2010, Institute of Industrial Science, University of Tokyo., 10/2010
  • 21st Century COE Award, Japan Society for the Promotion of Sciences., 8/2008
  • Outstanding Leadership Presentation Award, Tokyo Institute of Technology., 7/2007

Expertise

Advanced Multifunctional Composite Materials; Nanocomposites; Additive Manufacturing; Multi-Scale Modeling and Material Characterization; Micro and Nanotechnologies; Computational Mechanics; Multi-disciplinary Design Optimization.

Interests

Dr. Dalir’s research interests have revolved around different topics in the area of mechanical, automotive and aerospace engineering. His primary research interests are within the general area of Solid Mechanics and specifically on stress, modal and thermal analysis of mechanical and aerospace structures; computational mechanics; multi-disciplinary design optimization; composite materials and damage mechanics; and multi-scale modeling and material characterization.